Toy Kinetic Energy tester
My Q Kinetic Energy tester is used to detect the maximum kinetic energy generated by the fired bullets of Projectile toys or the launched bows. It meets standards: ISO 8124-1, GB6675-2, EN-71-1, ASTM F963.
Sharp Edge Tester
My Q Sharp Edge Tester is suitable for sharp edge testing as per 16CFR, ISO 8124-1, GB6675-2 and ASTM F963 standards.
Transportation Vibration Tester
My Q Transportation Vibration Tester is suitable for Simulation of transport shaking test ,ASTM D999 vibration meter, ISTA vibration meter .
Small Part Cylinder
My Q Small Objects Choke Tester mainly used to determine the potential hazards of suffocate, suction, swallow, etc, which results from the toys or other articles with small parts used for the children below 3 years old.
Sharp Point Tester
My Q Sharp Point Tester is used to determinate that points on toys and other articles intended for use by children under 8 years of age, and such points exposed in normal use or as a result of reasonably foreseeable damage or abuse of such toys and articles, present a potential risk of injury by puncture or laceration.
Standard Test Finger Probe & Accessibility Probe
My Q Standard Test Finger Probe & Accessibility Probe is used to determine whether the hazardous parts of toys can be touched. If it is accessible, then conduct the related test according to standards so as to reduce the damage hazards children EN-71-1 section 8.10
ASTM F963 section 3.1.2,
16CFR 1500 section 48 and 49
ISO 8124-1 section 5.7
GB6675-2 section 5.7 forEN-71-1 section 8.10
ASTM F963 section 3.1.2,
Mouth-Actuated Tester
My Q This Mouth Toy Durability Tester is suitable for the test of the safety of the Mouth-Actuated Toys, such as whistles with a ball, the sounders with a reed and other toys. This tester will blow-off certain volume gas in a certain speed and inhale the toy, blow-off and inhale alternately for 10 times, after the test, you should test the toy and the deciduous parts whether they are findings EN 71-1, ISO 8124-1, ASTM F963 , GB 6675.2
Dynamic Strength Tester & 2 M/S Tester
My Q This Dynamic Strength Tester is mainly used to test the dynamic strength of wheeled ride-on toys. Can simulate driven toys vertically hit the inelastic step in a steady speed of 2m /S ± 0.2 /S, then observe the damaged condition. Applied to toy bicycles, scooters, roller-skate and etc. EN71-1, ASTM F963, ISO 8124-1, GB 6675
Toys Scooter Steering Tubes Strength Tester
My Q Toys Scooter Steering Tubes Strength Tester apply to test the strength of toy scooter steering tubes,including resistance to downward forces and resistance to upward forces.toys testing instruments
EN Impact Test Table
My Q Impact Test Apparatus is used for the impact testing in the situation that simulating the toy material or imitation protection device toys are misused. Determine after impacting whether small parts, hazardous sharp edges , hazardous sharp points or hazardous driving mechanisms have become accessible. toys testing instruments
Pen-Cap Air Flow Tester
My Q Pen cap air flow tester mainly be used to test the safety of the caps for writing and marking instruments which are designed or clearly intended for use by children up to 14 years of age. However, Caps for writing and marking instruments which are not designed or intended for use by children, e.g. jewellery pens, expensive fountain pens, professional technical pens, are not be test by this method . toys testing instruments
Length Of Ropes And Chains Tester
My Q EN 71 Part 1 Length of Ropes and Chains Tester used to measure length for the ropes, chains or wires on toys. EN-71-1 section 8.20 , 8.40, ISO 8124-1 section 5.11.1, GB6675-2 section 5.11.1, EN 12221-2 section 5.3. toys testing instruments
Motor Horizontal Brake Performance Tester
My Q This Brake Test Machine is mainly used to test the motor brake performance of electric ride-on toys . Principle: Load the toy a suitable static strength load. Measuring the force required to pull the toy on a horizontal plane covered with a surface of abrasive paper (aluminium oxide P60) at a constant speed of (2 ± 0,2) m/s. The motor shall be considered to supply sufficient braking if:
Brake Performance Tester
My Q this Brake Performance Tester, the tilt angle of the ramp is adjustable. The angle adjustment range is 0 ~ 45 degree. Can be used to assist test the locking device of collapsible toys, the stability of toys, the brake performance of ride-on toys, etc., need to used with specified weight. toys testing instruments
Ball Impact Tester
My Q Ball Impact Tester is used to test the impact resistance of all rigid toys that cover the face, such as goggles, space helmets or face shields. According to the standard, after testing, the toys shall not produce sharp edges, sharp points or loose parts which could enter the eye. This applies to toys with cut-out eye holes as well as items that cover the eyes. toys testing instrunents
Electric Pencil Hardness Tester
My Q hardness pencil scratch the surface of the coating film to test the surface hardness of the coating film layer, hardness pencil fixed at an angle of 45º, so that the front end of the pencil center and the surface of the coating film layer in contact with the appropriate load, according to a certain speed (JIS standard 0.5mm / s) to move the test platform so that the surface of the coating film layer moving through the pencil center, the coating film layer will not cause damage (scratch) the softest pencil grade can be considered as the coating film Layer hardness. toys testing instruments
Color Fastness To Dry Cleaning
My Q Dry Cleaning Cylinder used to determine color fastness to dry-cleaning and chlorinated pool water, besides, to prepare samples for flammability testing. Meshed with various types of combustion tester, Use tetrachlorethylene to wash the surface flame retardants.
Digital Cap Torque Tester
My Q ST-B series Digital Cap Torque Tester is an intelligent metro logic instrument, it is designed for detecting and calibrating the torque torsion of approval and closure of various caps. It is adapted with clamps. Clamp installation is easy, rapid.and its diameter attach to 200mm. It has Printer inside.and has RS-232C output, can transmit the data to computer for analysis and printed more. toys testing instruments
Push Pull Test Stand
My Q Push Pull Test Stand is an assistant tool for push-pull test of toys. Applied with Push Pull Gauge, is specialized in tension/Compression, Insertion/withdraw and fracture test in every trade and scientific research organization. With gear drive and manual operation, adjustable test stand can be moved up and down to set orientation. Simpleness, stability, expeditiousness and appreciating batch test. toys testing instruments
Hook Test Fixture For Cords And Loops
My Q Hook Test is an auxiliary tool to measure perimeter for Loops and Cords, so as to determine whether length of ropes complies with safety requirements.ASTM F963 toys testing instruments
Clamp For Wheel Tension
My Q Wheel tension clamp is the assistant tool used for toys tension test. Mainly used for toy car wheels tension test. It meets standards: EN-71-1, ASTM F963, 16CFR 1500, ISO 8124-1, GB6675-2.
Wide-Mouth Clamp
My Q Mouth clamp is the assistant tool used for toys tension test.It is a wide mouth clamp ,meets standards: EN-71-1, ASTM F963, 16CFR 1500, ISO 8124-1, GB6675-2. toys testing instruments
Noise Testing Stand
My Q EN 71 part 1 Noise Testing Stand is the test stand for noise meter, meets standards: EN-71-1, ISO 8124-1, GB6675-2, ASTM F 963, 16CFR 1500. toys testing instruments
Toys Chest Lid Tester
My Q The Toys Chest Lid Tester applies to test the durability of toys box cover. It uses fixtures to drive the toy box cover move, after simulating a certain number of opening and closing movements, check whether the toy box lid hinge part’s functions are in good condition. toys testing instruments
Seam Clamp For Toys Tension Test
My Q Seam Clamp is the assistant tool used for toys tension test and is a Seam Clamp Metal Clamps, 16CFR 1500 Metal Clamps, ISO 8124-1 GB6675-2 Metal Clamps .
Small Torque Fixture
My Q Torque Test for Toys Torque Clamp Middle is the assistant tool for toys torque test. ISO8124-1 section 5.24.5 GB 6675-2 section 5.24.5 EN71-1 section 8.3 , EN 16890-2017 Section 8.3.1 ASTM F963 section 8.8, 8.16, 8.24.4.3 16CFR 1500 section 51, 52, 53
ASTM Flexure Tester
My Q ASTM Flexure Tester is used to test the metallic wires and other metallic components of a toy or part of a toy after repeated flexing, whether the toy will break and produce hazardous sharp points, or protrude through any surface covering of the toy.
Long - Mouth Clamp
My Q Long Mouth Clamp is the assistant tool for toys torque test. EN-71-1 Section 8.4, 8.34, EN 16890-2017 Section 8.3.1, ASTM F963 Section 8.9, 8.18.8, 16CFR 1500 Section 51, 52, 53, ISO 8124-1 Section 5.24.6, 5.31, GB6675-2 Section 5.24.6, 5.26
.
Two Pronged Clamp
My Q Pronged Clamp is the assistant tool used for toys tension test. It meets standards: EN-71-1, ASTM F963, 16CFR 1500, ISO 8124-1, GB6675-2.
Three Pronged Clamp
My Q Three Pronged Clamp is the assistant tool used for toys tension test. It meets standards: EN-71-1, ASTM F963, 16CFR 1500, ISO 8124-1, GB6675-2.
Average Speed Tester
My Q Average Speed Tester is mainly used to test the mobile speed of the electric ride-on toy, can evaluate the motor braking performance and the maximum design speed of a toy cars.
Motor Brake Performance Testing Ramp
My Q Motor Brake Performance Tester is a longer 10 degree ramp, mainly used for the brake test of electric ride-on toys.
Small Ball Test Template
My Q Small Ball Test Fixture is use to examine a toy up of whether small ball accessories may result in the child swallow, stop breath way and esophagus to cause choking danger or not.
Large Torque Fixture
My Q Large Torque Fixture is the assistant tool for toys torque test. ISO8124-1 section 5.24.5, GB 6675-2 section 5.24.5, EN71-1 section 8.3, EN 16890-2017 Section 8.3.1, ASTM F963 section 8.8, 8.16, 8.24.4.3, 16CFR 1500 section 51, 52, 53
Ring Gauge
My Q Ring Gauge test is used for reducing the risk of asphyxiation from end closures for writing and marking instruments. It relates to such instruments which in normal or foreseeable circumstances are likely to be used by children up to the age of 14 years.
Digital Force Gauge
My Q push pull scale can measure tension, compression force accurately, and durable, is an ideal product for industrial quality control, research and development field strength test.
Noise Meter
My Q Noise meter is used to measure the sound pressure level comes form sound toys in a predetermined distance. It meets standards: EN-71-1, ISO 8124-1, GB6675-2, ASTM F963, 16CFR 1500.
Flat Clamp
My Q Toys Flat Clamp is the assistant tool used for toys tension test EN-71-1 , ASTM F963 , 16CFR 1500 ,ISO 8124-1 ,GB 6675-2
TTF Tensile Tester
My Q TTF tensile tester is used for providing large and stable tensile during the tension test. in tensile. It is mostly used for the toys’ destructive tension test.
Bite Tester
My Q Bite Tester is used to test whether the toys has cracked after bite test, and if it has produced hazardous sharp points, hazardous sharp edges, and hazardous small parts after crack.
Tension Clamp
My Q Tension Clamp is the assistant tool used for toys tension test. Meeting the standards: EN-71-1, ASTM F963, 16CFR, ISO 8124-1, GB6675-2.
EN Drop Tester
My Q The EN Drop Tester is to determine the toys fall on the floor through a certain height, fall in a certain number, then check whether the hazardous sharp points, hazardous sharp edges, hazardous small parts and hazardous driving mechanisms have become accessible.
Gap Test Round
My Q Gap Test Round is used to determining the whether the palpable gap on toys is a risk. To prevent children from pinching and crushing.
Liquid Leak Test Needle
My Q Liquid Leak Test Needle is used to detect whether the liquid-filled toys have leakage after applying 5N force through a steel needle.
Hair Clamp
My Q Hair Clamp is the assistant tool used for toys tension test. Mainly applied to test toys wig, beard hair and other hairy parts.
Bench Vice
My Q Bench Vice is the assistant tool used for toys tension test. It is the assistant tool used for toys tension test. Mainly used to fix the main body of toys..
Feeler Gauge
My Q Feeler Gauge is used to determine whether parts on toys can be stepped up so as to determine whether the tensile testing is necessary.
Static Strength Test Load
My Q This series of weight are mainly used for dynamic strength and stability test of ride-on toys, weight should change with children’s different ages.
Test Platform Block
My Q This instrument is the No.4 object on the picture above, mainly for regulating the center of gravity of the test weight to height 400mm.
Dynamic Strength Test Load
My Q weight is mainly used for wheeled ride-on toy dynamic strength and scooters braking performance test , toys for the children under 36 months, should use the 29.5kg weight while toys for the children are 36 month and over should use the 54.5kg weight. Configuring two arms and seat belts.
Toy Handlebar Resistance To Separation Tester
My Q Toy Handlebar Resistance To Separation Tester is used to test the anti-separation performance of toy handlebars. Standards: ISO 8124-1 5.30.
Electronic Metronome
My Q Metronome can emit a steady beat at various speeds, this machine is an electronic metronome, mainly used for speed control when auxiliary toy testing. Standards: ISO 8124-1, GB 6675.2, EN71-1, ASTM F963.
Wheeled Toys Tumble Test Steps
My Q This instrument is mainly used to tumble test for Wheeled toys weighing more than 3 lb (1.4 kg) but not more than 10 lb (4.5 kg). Standards: ASTM F963 section 8.7.3.
Plastic And Film Thickness Gauge
My Q Plastic and Film Thickness Gauge is suitable to determine plastic film and slice thickness with mechanical measurements. Standards:EN-71-1, ISO 8124-1, ASTM F963, GB 6675-2, ISO 4593.
Toy Tester Jaw Entrapment Risk Test Fixtures
My Q It is used for determine whether there is the risk of jaw entrapment in handles and steering wheels that are located such that they are accessible for teething in the following categories of toys intended for children under 18 months of age: activity tables intended to be played with by a standing child, large bulky toys, stationary floor toys, push toys intended to be pushed by a child walking upright, and ride-on toys.
Part 1 Rattle Test Template Stand
My Q It’s auxiliary stand to support My Q -M46 Rattle Test Template & My Q -M47 Small Ball Test Template, so as to it be more convenient to do test.
50N.M Digital Torque Tester
My Q Series digital torque tester is R&D for testing and measuring many kinds of torque. The Meter is applied with the measured and calibrated torque of motorize or air-driving clamps, torque screwdriver and torque spanner. It is applied with the test of wrench force, wrest fractured force. The gauge is used in Electric industry, Light industry, Machinery manufacture, Scientific research, etc.
Push-Pull Scale Force Gauge
My Q Push-Pull Scale Force Gauge can measure tension, compression force accurately, and durable, is an ideal product for industrial quality control, research and development field strength test. All kinds of models has the zero adjustment for tare weight, and the scale dial is easy to read. Many ranges are offered, calibrated in Pounds, Kilograms, or Newtons.
Drop Teste
My QASTM Drop Tester is to determine the toys fall on the floor through a certain height, fall in a certain number, then check whether the hazardous sharp points, hazardous sharp edges, hazardous small parts and hazardousdriving mechanisms have become accessible.
ASTM Pacifier Tester
My Q ASTM Pacifier Tester used to detect “the pacifier” toys conform to safety standards.
Part 1 12mm Feeler Gap Gauge
My Q Soft-filled toys and soft-filled parts of a toy, containing fibrous filling material shall have at least one covering such that, after tension test, it shall not be possible to insert the front part of a 12 mm diameter rod with a fully radiused end through any one opening in the seam or cover material by more than 6 mm, using a maximum force of 10 N.
Torque Gauge
My Q This series of Torque Gauge are handheld torsion meter and they are ideal tools for torsion testing and little torsion measuring. The instrument is configured Two-way calibration, so two-way test is possible.
